The H310 Loader can be ordered with a single-point hydraulic connection that also incorporates the connection point for any electrical needs. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.
Over time, increased width in tractor hoods have caused issues with available space for running traditional oil lines of a loader along the boom, making them more susceptible to damage.
To improve this situation, the oil lines have been routed through the boom arm and the torque tube, improving line protection and the appearance of the loader.
John Deere loaders are easily removed and reinstalled on tractors without tools. The parking system allows removing or attaching the loader to the tractor in minutes without the need for tools.
To remove or park the loader, apply slight down pressure to the loader boom with the bucket dumped at approximately a 30-degree angle. With the tractor in park, lower the parking stands and place the mast pins in the open position.
Utilizing the boom circuit with the tractor in neutral, rotate the mast forward until the mast has rotated past the pin location on the mounting frame by extending the lift cylinder. Now using the bucket circuit, roll back the bucket until the mast is removed from the pocket and will clear the tires.
With the tractor in park, shut the engine off and relieve the hydraulic pressure as indicated for the tractor (rotating the joystick). Disconnect or open the single-point hydraulic connector (or remove couplers if no single point is installed).
Store the loader half of the single-point connector or hoses, and back away from the loader.
A hydraulic shut-off valve is included with the M & R-Series Utility & Ag Loaders to ensure the loader does not lower suddenly. For example, this allows the boom to be locked out when someone is required to be located under the loader boom for service work on the tractor. It should not be used for extended periods of time unless an appropriate support stand is also utilized.
Fast bucket cycle times are important to dump the load from the bucket as quickly as possible, in order to be as productive as possible, while completing loading operations. The bucket cylinder design can have a major impact on this cycle time, especially for the mechanical self-leveling (MSL) loaders.
Therefore, all MSL H-Series Loaders utilize false rod bucket cylinders. A false rod cylinder has a smaller displacement of oil requirement on the head end of the cylinder, which allows this cylinder to dump much faster than a normal cylinder.
An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.
Performance
NOTE: Check bale-handling capability of tractor before use.
Cost of ownership
Reasons for turning LSS off include:
The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.
LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.
Maximum lift height (A) | 3855 mm 151.8 in. |
Lift capacity at full height | Measured at pivot (U) 3746 lb 1699 kg |
Boom breakout force | Measured at pivot (Y) 2677 kgf 5902 lbf |
Bucket rollback force capacity | At ground-level line (ZZ) 3059 kgf 6744 lbf |
Clearance at full height - bucket dumped (C) | 2826 mm 111.3 in. |
Dump angle, degrees (E) | -7 degree (angle) |
Rollback angle, degrees (G) | 42 degree (angle) |
Model | 6105R/6115R/6125R |
Front tire | 16.9R24 |
Rear tire | 18.4R38 |
Front axle configuration | MFWD w/ Limited Slip Differential |
Wheelbase | 2580 mm 101.6 in. |
Pump capacity | 114 L/min 30.1 gpm |
Rated pressure | 2901 psi 200 bar |
Base weight | 1356.8 kg |
Leveling configuration | Mechanical Self Leveling (MSL) |
Bucket used | Materials 73 in. Materials 1850 mm |
Bucket weight | 620 lb 281 kg |
Lift capacity at full height | Measured at pivot (U) 3746 lb 1699 kg Measured at 800 mm ahead of pivot (V) 1846 kg 4070 lb |
Lift capacity at 59 in. (1500 mm) | Measured at pivot (W) 2187 kg 4822 lb Measured at 800 mm ahead of pivot (X) 2090 kg 4608 lb |
Boom breakout force | Measured at pivot (Y) 2677 kgf 5902 lbf Measured at 800 mm ahead of pivot (Z) 2335 kgf 5148 lbf |
Bucket rollback force capacity | At maximum height (VV) 1513 kgf 3336 lbf At 59-in. (1500-mm) lift height (XX) 3003 kgf 6620 lbf At ground-level line (ZZ) 3059 kgf 6744 lbf |
Dimensions | Maximum lift height (A) 3855 mm 151.8 in. At full height - bucket level(B) 3661 mm 144.1 in. At full height - bucket dumped (C) 2826 mm 111.3 in. |
Overall length (I+F), ft (m) | 5 m 16.4 ft |
Digging depth (H) | 31 mm 1.2 in. |
Reach | At maximum height (D) 800 mm 31.5 in. At ground level - bucket level (F) 2422 mm 95.4 in. |
Bucket angle | Dump angle, degrees (E) -7 degree (angle) Rollback angle, degrees (G) 42 degree (angle) Dump angle, ground -95 degree (angle) |
Cycle times | Loader raise, seconds 2.3 seconds Loader lower, seconds 1.9 seconds Bucket dump, seconds 1.4 seconds Bucket rollback, seconds 1.4 seconds |